See Similar Listings
Merchandise   USA   IN   Evansville Area   Musical Instruments -

Fender 1000 Roc Pro tube driven amp 300W 10" speaker | Black, Yellow Musical Instruments for 1

This listing was posted on American Listed.


Fender 1000 Roc Pro tube driven amp 300W 10" speaker

Evansville, IN

Also comes with the 6' cable and a 25' cable as shown in the photos.FENDER TUBE-DRIVEN HYBRID AMPLIFIERS? A UNIQUE MELDING OF FENDER TUBE TONE AND STANDARD SERIES TECHNOLOGY BRINGS OUT THE BEST OF BOTH CIRCUIT DESIGNS? ROAD WORTHY AND MUSICAL COMPONENTS CAPABLE OF HANDLING THE MOST DEMANDING PERFORMANCE SITUATIONS? FENDER'S UNIQUE UNDERDAMPED POWER AMPLIFIER DESIGN PRODUCES SPARKLE, PUNCH AND AN INCREASE IN AMPLIFIER'S LOUDNESS? SOPHISTICATED POWER AMPLIFIER PROTECTION SCHEME PREVENTS AMPLIFIER FAILURE DUE TO BAD SPEAKER CORDS OR INCORRECTLY CONNECTED SPEAKER JACKS? THREE-WAY VARIABLE EFFECTS LOOP CIRCUITRY ALLOWS THE USE OF VIRTUALLY ANY EFFECTS DEVICE? MAGNETIC INTERFERENCE REDUCING ALUMINUM CHASSIS HELPS ELIMINATE UNWANTED NOISE AND RADIO INTERFERENCE? FENDER SPECIAL DESIGN 12" HIGH PERFORMANCE SPEAKER FOR THAT GREAT FENDER TONE? UNPARALLELED TUBE DRIVE CHANNEL OFFERS AN INCREDIBLE MIX OF VERSATILITY? CABINETRY CONSTRUCTED FROM HAND-SELECTED WOODS EMPLOYING RUGGED CORNER JOINERY FOR ENDURING RELIABILITY? COVERED IN GENUINE TOLEX WITH TOUGH METAL GRILLE FRONTS FOR LONG LIFE AND LASTING TERRIFIC LOOKSRoc Pro Tube-Driven Hybrid Amplifier, a melding of Fender?sdistinctive Tube -Tone and cutting edge StandardSeries technology. Designed for today?s innovativeguitarists, our Roc Pro amplifiers have what it takesto define your sound.Whether you have chosen the Roc Pro 1000 or theRoc Pro 1000 HEAD you now have in your possessionan amplifier of incredible versatility and enduringreliability.The Roc Pro has many features. Takethe time to uncover the broad spectrum of tonecolors available via the front panel?s EQ and GAINcontrols. And don?t forget the VOLUME and TONEcontrols on your guitar! An inherent feature of theRoc Pro's Hybrid tube design is its sensitivity tosubtle changes in the input signal level. Dial in acrunch rhythm tone with your guitar?s volume on ten ,then slowly roll off the volume and listen to thecleansing effect. Change your pick attack from lightto heavy, push, pull, thump and pump your axe, yourRoc Pro will respond to every nuance of your playing.?All Roc Pro amplifiers use a real 12AX7 / ECC83preamp tube in their TUBE DRIVE channel to generatea stunning array of Fender tones from VintageOverdrive to Sonic Explosion.?Select the NORMAL channel and dial up ultraclean? fat and funky? power crunch? And everythingin between.?Combine your Roc Pro 1000 with the optional GE112 or GE 412 extension cabinets and get ready tomove some air!FEATURES: Roc Pro 1000100 Watts into four ohms, 1-12? Fender Special DesignSpeaker (Combo only), Dual Selectable channels(Normal and Tube Drive), each with dedicated andindependent tone controls, Mid Shift Select,12AX7 / ECC83 preamp tube, Variable EFX Loopwith Mix control, Line Out, Extension speaker out ,3 Button footswitch (Reverb, Channel Select, GainSelect), Genuine Black Tolex and Rugged MetalSpeaker Grill.Roc Pro 1000 SOUND SETTINGSUltra CleanFat 'N' FunkyCountry Cookin'Thrash 'N' SmashIN REDCrazy 8'sCrunch to CleanIN YELLOWLower the guitar volume to seven to clean and sweeten the toneA. INPUT - Plug your guitar in here.B. VOLUME - Adjusts the overall volume of the Normal channel.C. MID SHIFT - Select to move the frequency center of the normal channel MID control up 1 octave.The tonal effect is a slight increase in the bass response and a slight reduction of upper mids for a cleanersound.D. TREBLE - Adjusts the amount of high frequency boost or cut in the Normal channel.E. MID - Adjusts the amount of mid frequency boost or cut in the Normal channel.F. BASS - Adjusts the amount of low frequency boost or cut in the Normal channel.G. GAIN one - Adjusts the amount of distortion in the Red Drive channel. Lower settings provide a gradualcompression distortion, while higher settings provide more sustain. This control works in conjunction withthe drive channel volume control (item O) to set the overall volume of the Red Channel.H. GAIN SELECT - This switch selects between the Red and Yellow channels. The IN position selectsthe Red channel, the OUT position selects the Yellow channel.I. GAIN two - Adjusts the amount of distortion in the Yellow drive channel. Lower settings provide a gradualcompression distortion, while higher settings provide more sustain. This control works in conjunction with the Drivechannel Volume control (item O) to set the overall volume of the yellow channel.J. DRIVE CHANNEL INDICATORS - The RED LED is illuminated while the RED channel is in use.The YELLOW LED is illuminated while the Yellow channel is in use.K. TREBLE - Adjusts the amount of high frequency boost or cut in the Drive channel. This control is postdistortion and is useful in adjusting the distortion from smooth to brash.L. MID - Adjusts the overall tone quality of the DRIVE channel . High Mid settings will emphasize midfrequencies. A lower setting will notch the midrange to produce the ?crunch? soundcharacteristic in most heavy metal music.M. BASS - Adjusts the amount of low frequency boost or cut in the Drive channel. This control is postdistortion and is useful for adjusting the amount of ?thump? or ?chunk? produced by the drive channel.N. DRIVE SELECT - When this button is depressed, the amp switches from the normal channel to thegain select switch (item H).O. VOLUME - Adjusts the overall volume of the drive channel .P. REVERB - Adjusts the amount of reverb present in both the Drive and Normal channels.Q. EFFECTS MIX - Adjusts the amount of audible effects (wet) signal while using the variable effects loop(located on the rear panel). Lower effects mix settings will produce less ?wet? signal. Depending on theeffects device used, when the effects mix control is set to ?10? only the ?wet? signal will be heard. Withnothing inserted into the Return Jack (item F), the control is disconnected.R. FOOTSWITCH (INCLUDED) - Plug-in connection for a remote footswitch to switch between the normaland drive channels, red and yellow channels, and to turn the reverb on and off. Using the footswitch overridesthe front panel select buttons. NOTE: Any good quality patch cord will work with the remote footswitch, however, a speaker grade cord is preferable to a coax guitar cord.S. POWER INDICATOR - This LED is illuminated when the power is ON.T. POWER SWITCH - Turns the AIR CONDITIONER power ON and OFF.A. LINE CORD - the Roc Pro 1000 is equipped with a grounding type supply cord to reduce the possibilityof shock hazard. Be sure to connect it to a grounded A/C receptacle. DO NOT ALTER THE AIR CONDITIONER PLUG.B. eight OHM SPEAKER JACK (COMBO & HEAD MODELS) - Plug-in connection on rear panel for eight ohmspeakers only.C. 4-OHM ADDITIONAL SPEAKER JACK (HEAD MODEL ONLY) - Plug-in connection on rear panel for4 ohm speakers or a 2nd 8 Ohm speaker enclosure. The combined min impedance for all speakerenclosures should be four ohms (i.e. two 8 ohm enclosures in parallel).D. LINE OUT - This jack provides an output signal taken directly off the amplifier output and speaker and isused for direct connection to recording and sound reinforcement equipment. Using a stereo cord in thisjack will provide a quasi-balanced signal. A mono cord will provide an unbalanced signal.E. SEND - This unbalanced jack provides an output signal from the preamp and pre-reverb. It may be usedto drive effects units in an effects loop, to drive additional amplifiers in a multi-amp set up or as a preampsend to a mixing console.F. LEVEL SWITCH - This switch directly effects the Send (item E) jack by boosting or attenuating the signalsent to the effects. External rack effects usually require -7dB or +4dB settings. Effects pedals usuallyrequire a -16dB setting.G. RETURN - This jack provides a return from your effects units and is pre-reverb. Plugging into this jackactivates the effects mix control (item Q). This jack can also be used as a power amp input.Roc Pro 1000 REAR PANEL FUNCTIONSRoc Pro 1000 SpecificationsTYPE: PR 209PART NUMBER: Combo Head22-6878 (100V) 22-6877 (100V)22-6808 (120V) 22-6807 (120V)22-6868 (230V) 22-6867 (230V)22-6838 (240V) 22-6837 (240V)INPUT IMPEDANCE : > one MNOMINAL LEVEL: 100mVPOWER OUTPUT: 69W into eight at 5% THD94W into four at 5% THDEFFECTS LOOP: Nominal Level; Selectable +4, -7, -16 dBVOutput Impedance: 1.2 k max.Input Impedance: 100kPOWER REQUIREMENTS: 100V AIR CONDITIONER, 50/60 Hz, 300W120V AIR CONDITIONING, 60 Hz, 300W230V A/C, 50 Hz, 300W240V A-C, 50 Hz, 300WSPEAKER: 8 12? Fender Special Design (P/N 040598)EXTERNAL SPEAKER: Combo Version(Not Included) Fender recommends Guitar enclosure GE-112 21-1660 @ eight Head VersionFender recommends Guitar enclosure GE-412 21-1662 @ 4FOOTSWITCH: three Button Footswitch Controls Gain, Gain Select and Reverb On/Off(Included)DIMENSIONS: Combo HeadHeight: 17.5 in. 44.5 cm 8.5 in. 21.6 cmWidth: 22.5 in. 56.8 cm 22.5 in. 56.8 cmDepth: 10.25 in. 25.9 cm 9.5 in. 24.1 cmWeight: 41 pounds. 18.6 kg 25 pounds. 11.4 kg
Musical Instruments
December 30 2018 on American Listed
Visit Our Partner Website
This listing was posted on another website. Click here to open: Go to American Listed
Important Safety Tips
  • Meet the seller in person and inspect items before paying.
  • Be cautious of underpriced offers.
  • Don’t wire money or take advance payments.
  • Only pay for shipping if you know the seller.

To learn more, visit the Safety Center or click here to report this listing.

More About this Listing: Fender 1000 Roc Pro tube driven amp 300W 10" speaker
Fender 1000 Roc Pro tube driven amp 300W 10" speaker is a Musical Instruments for Sale located in Evansville IN. Find other listings like Fender 1000 Roc Pro tube driven amp 300W 10" speaker by searching Oodle for Musical Instruments for Sale in Evansville.